The Exterior™ Projection 1000 is an unparalleled, powerful tool for permanent outdoor installations to integrate textures, patterns and graphics for limitless creative exterior lighting designs.
Sporting high impact and low maintenance, this advanced, IP66-rated LED projector offers sharp image quality, dynamic features and great reach over huge distances.
Creating custom gobos for building facades
Flat-field, high-contrast image projection with wide zoom range
Fully weatherized with low maintenance and running
Color mixing: CMY, independently variable 0 - 100%
Color wheel: 7 interchangeable colors + open
Gobo wheel: 7 rotating gobos plus open, indexing, variable rotation
Gobo animation wheel: Indexing, continuous rotation with variable angle, speed and direction
Prism: Prism wheel with 2 interchangeable prisms, prism rotation and indexing
Frost filter: Motorized, variable
Zoom: 10° - 44° (cut-off angles)
Focus: Motorized, variable 3 m (9.8 ft.) to infinity
Dimming: Electronic, constantly variable 0-100%, 16-bit control
Shutter: Electronic, strobe and pulse effects, instant open and blackout
Control and Programming
Control options: DMX, RDM, standalone
Configuration, addressing and status: Onboard control panel with OLED display or via RDM
8-bit control: CMY, color selection, gobo selection, prism, frost, animation
16-bit control: Gobo indexing and rotation, zoom, focus and intensity
DMX channels: 20
DMX compliance: USITT DMX512-A
RDM compliance: ANSI/ESTA E1.20
Optics
Light source: 440 W white light LED engine
CRI (Color Rendering Index): 72
Color temperature: 6500 K (±250 K)
LED lifetime: 20,000 hours (to >70% luminous output)*
LED manufacturer: Appotronics
*Figure obtained under manufacturer's test conditions
Photometric Data
Cut-off angle: 10° - 44°
Luminous intensity:
At 10° zoom: 11,500 lumens
At 16° zoom: 15,000 lumens
At 40° zoom: 16,800 lumens
Center Peak:
At 10° zoom: 731,000 cd
At 16° zoom: 311,000 cd
At 40° zoom: 42,000 cd
Construction
Housing: Cast aluminum
Finish: Hard anodized, white or metallic grey lacquered
Front glass: 5 mm (0.2 in.) anti-reflection coated tempered glass
Ingress protection: IP66
Impact resistance: IK08 (with control panel display cover plate installed)
Corrosion resistance: C5-M (very high corrosivity / marine, ISO 12944)
EPA (Effective Projected Area): 0.28m²
Installation
Mounting: Adjustable yoke
Location: Suitable for wet locations. Do not immerse in water.
Orientation: Any (sides must be kept vertical)
Minimum distance to illuminated surfaces: 0.5 m (20 in.)
Connections
Power cable entry: IP66 cable gland
Power connection: 1.8 m (5.9 ft.) cable tail with bare ends
Power cable type: EU models: H07RN-F 450/700V, Ø10 mm
US models: SJTW 14AWG, 300V, Ø9.3 mm
Data cable entry: IP66 cable gland
Data connection: 1.8 m (5.9 ft.) combined input + output cable tail with bare ends
Electrical
AC power: 100-120/200-277 V nominal, 50/60 Hz
Power Supply: Auto-ranging electronic switch-mode
Typical half-cycle RMS inrush current: 15.5 A
Surge protection: 4 KV
Idle power (zero intensity, no effects applied): 75 W
Typical Power and Current
120 V, 60 Hz: 645 W, 5.5 A, PF 0.98
230 V, 50 Hz: 635 W, 2.9 A, PF 0.95
277 V, 60 Hz: 635 W, 2.6 A, PF 0.90
Figures are typical, not maximum. Measurements made at nominal voltage with all LEDs at full intensity. Allow for a deviation of +/- 10%.
Thermal
Cooling: Convection, internal forced air
Total heat dissipation (calculated): 2350 BTU/hr.
Maximum surface temperature: 85° C (185 ° F)
Maximum ambient temperature (Ta max.): 45° C (113° F)*
Minimum ambient temperature (Ta min.): -30° C (-22° F)**
*Above this temperature, the fixture regulates output to protect from overheating. **For instant wake-up with no warm-up mode, leave power applied constantly in ambient temperatures below 0° C (32° F).
Approvals
EU safety: EN 60598-2-1, EN 60598-2-5 (EN 60598-1), EN 62471, EN 62493
EU EMC: EN 55015, EN 55032, EN 55103-2, EN 61000-3-2, EN 61000-3-3, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61547