Exterior Wash™ 310 is a powerful, compact and energy-efficient LED lighting fixture designed to illuminate large structures, building facades and bridges. A discreet, optional snoot integrates seamlessly with the slick design of the fixtures. It has built-in display for ease-of-use, a wide selection of beam angles and is fully IP-rated for permanent outdoor use. The Exterior Wash 310 is designed for superior color mixing applications and is based on quad-color premixed LEDs.
Features
Uniform color mixing with 6 beam angle options
Functional and discreet optional snoot which integrates with the design of the fixtures
Setting, addressing, standalone programming: Control panel with OLED display
DMX channels: 3-5 depending on DMX mode
Receiver: RS-485
DMX compliance: USITT DMX512-A
RDM compliance: ANSI/ESTA E1.20
Firmware update: Serial upload via DMX link
Optics
Light source: 19 x RGBW quad-color LEDs
Minimum LED lifetime: 50,000 hours (to >70% luminous output)*
LED manufacturer: Cree
Beam Angle Options:
No diffuser: 10.5°
Narrow diffuser: 14°
Medium diffuser: 24°
Wide diffuser: 43°
Very wide diffuser: 63°
Asymmetric diffuser: 61° x 16°
*Figure obtained under manufacturer's test condition
Photometric Data
Total luminous output: 4900 lumens
Construction
Housing: Cast aluminum
Color: Light grey (white, black or other colors available on request)
Ingress protection rating: IP66
Surface treatment: Anodized and electrostatic powder-coated
Effective Projected Area (EPA): 0.1 m² including snoot
Impact resistance: IK08 (with control panel display cover plate installed)
Corrosion resistance: C5-M (very high corrosivity / marine, ISO 12944)
RoHS compliant
Installation
Mounting: Adjustable yoke
Orientation: Any
Minimum distance to illuminated surfaces: 0.2 m (0.6 ft.)
Connections
Power connection: 1.8 m (5.9 ft.) cable tail without connector
Power input cable type, EU models: H05RN-F 300/500V, 3 x 0.75 mm2, Ø 7 mm
Power input cable type, US models: SJOW 18AWG, 300V, WL F1, Ø 8 mm
Data connection: 1.8 m (5.9 ft.) open ended 5-conductor combined input + output cable tail
All cable entries: IP68 cable gland
Electrical
AC power: 100 - 240 / 277 V nominal, 50/60 Hz
Power supply unit: Integrated, auto-sensing multi-voltage
Power Consumption: 3 W (steady state, all LEDs at zero intensity)
Typical half-cycle RMS inrush current: 10.3 A
Surge protection: 4 KV
Maximum total power consumption: 185 W
Typical Power and Current
100 V, 60 Hz: 1.6 A, 160 W, PF 0.99
120 V, 60 Hz: 1.35 A, 160 W, PF 0.99
230 V, 50 Hz: 0.75 A, 160 W, PF 0.94
277 V, 60 Hz: 0.65 A, 160 W, PF 0.89
Measurements made with fixture in steady state at nominal voltage, ambient temperature (Ta) 20° C (68° F), all LEDs at full intensity. Allow for a deviation of +/- 10%.
Thermal
Cooling: Convection
Maximum ambient temperature (Ta max.): 45° C (113° F)*
Minimum ambient temperature (Ta min.): -30° C (-22° F)**
Maximum surface temperature, steady state, at 40° C ambient: 55° C (131° F)
Total heat dissipation (calculated, +/- 10%): 485 BTU/hr
*Above this temperature, the fixture regulates output to protect from overheating **Power must be maintained below -20° C (-4° F)
Approvals
EU safety: EN60598-2-5 (EN60598-1), EN62471, EN62493, EN60598-2-1
EU EMC: EN55015, EN61547, EN61000-3-2, EN6100-3-3, EN61000-4-2, EN6100-4-4, EN6100-4-5