Martin - Exterior Projection 500 MG, Narrow, EU

Martin - Exterior Projection 500 MG, Narrow, EU

The Exterior™ Projection 500 is a powerful fixture for integrating textures, patterns and graphics in outdoor lighting designs. The fixture can be used for bright and dynamic logo projection as well as precision framing.

Using advanced LED technology, it offers outstanding energy efficiency, compact size and unlimited creative possibilities.

Features

• Flat-field, high-contrast image projection
• Fully weatherized for trouble-free use with minimal maintenance in outdoor installations
• Packed with features, allowing huge creativity in setting up exciting lighting effects

Physical

• Length: 415 mm (16.4 in.)
• Width: 293 mm (11.6 in.)
• Height: 444 mm (17.5 in.)
• Weight: 17.5 kg (38.6 lbs.)

All figures include mounting yoke

Dynamic Effects

• Color wheel: 8 interchangeable colors + open
• Gobo wheel: 6 rotating gobos plus open, indexing, variable rotation
• Gobo animation: Variable speed linear animation effect
• Prism: Prism wheel with 2 interchangeable prisms, prism rotation and indexing
• Frost (wash effect): Motorized variable
• Focus: Motorized, variable 3 m (9.8 ft.) to infinity
• Dimming: Electronic, constantly variable 0-100%, 16-bit control
• Shutter: Strobe and pulse effects, instant open and blackout

Control and Programming

• Control options: DMX, RDM, standalone
• Control resolution: 8-bit DMX control of each color
• Configuration, addressing and status: Onboard control panel with OLED display
• DMX channels: 13
• DMX compliance: USITT DMX512-A
• RDM compliance: ANSI/ESTA E1.20

Optics

• Light source: 230 W white light LED engine
• CRI (Color Rendering Index): 72
• Color temperature: 8300 K
• LED lifetime: 20,000 hours (to >70% luminous output)*
• LED manufacturer: Prolight Opto

*Figure obtained under manufacturer's test conditions

Photometric Data

Narrow:

• Cut-off angle: 12°
• Total output: 5000 lumens
• Center peak: 203,000 cd

Medium:

• Cut-off angle: 22°
• Total output: 6100 lumens
• Center peak: 77,000 cd

Wide:

• Cut-off angle: 36°
• Total output: 5700 lumens
• Center peak: 28,000 cd

Very Wide:

• Cut-off angle: 50°
• Total output: 3400 lumens
• Center peak: 11,000 cd

Construction

• Housing: Cast aluminum
• Finish: Hard anodized, metallic grey lacquered
• Front glass: 5 mm (0.2 in.) anti-reflection coated tempered glass
• Ingress protection: IP66Impact resistance: IK08 (with control panel display cover plate installed)
• Corrosion resistance: C5-M (very high corrosivity / marine, ISO 12944)
• EPA (Effective Projected Area): 0.15 m2
• RoHS compliant

Installation

• Mounting: Adjustable yoke
• Location: Suitable for wet locations. Do not immerse in water.
• Orientation: Any (sides must be kept vertical)
• Minimum distance to illuminated surfaces: 0.5 m (20 in.)

Connections

• Power cable entry: IP68 cable gland
• Power connection: 1.8 m (5.9 ft.) cable tail with bare ends
• Data cable entry: IP68 cable gland
• Data connection: 1.8 m (5.9 ft.) combined input + output cable tail with bare ends

Electrical

• AC power: 100-240/277 V nominal, 50/60 Hz
• Power Supply: Auto-ranging electronic switch-mode
• Typical half-cycle RMS inrush current: 8.4 A
• Surge protection: 4 KV
• Idle power (zero intensity, no effects applied): 32 W, 0.3 A

Typical Power and Current

• 110 V, 60 Hz: 320 W, 2.9 A, PF 0.977
• 230 V, 50 Hz: 310 W, 1.4 A, PF 0.971
• 277 V, 60 Hz: 305 W, 1.2 A, PF 0.950
• Figures are typical, not maximum. Measurements made at nominal voltage with all LEDs at full intensity. Allow for a deviation of +/- 10%.

Thermal

• Cooling: Convection, internal forced air
• Total heat dissipation (calculated): 1100 BTU/hr.
• Maximum surface temperature: 85° C (185° F)
• Maximum ambient temperature (Ta max.): 45° C (113° F) *
• Minimum ambient temperature (Ta min.): -30° C (-22° F)**
• *Above this temperature, the fixture regulates output to protect from overheating.
• **For instant wake-up with no warm-up mode, leave power applied constantly in ambient temperatures below 0° C (32° F)

Approvals

• EU safety: EN 60598-2-1, EN 60598-2-5 (EN 60598-1), EN 62471, EN 62493
• EU EMC: EN 55015, EN 55032, EN 55103-2, EN 61000-3-2, EN 61000-3-3, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61547
• US safety: ANSI/UL 1598
• US EMC: CFR 47 Part 15 Class A
• Canadian safety: CSA C22.2 No 250.0
• Australia/NZ: RCM