Sound Projects - X-act V2 Sound Projects - X-act V2 Sound Projects - X-act V2 Sound Projects - X-act V2 Sound Projects - X-act V2 Sound Projects - X-act V2 Sound Projects - X-act V2
Sound Projects - X-act V2
Chainmaster - C1 Ultra

Chainmaster - C1 Ultra

Martin - VDO Atomic Dot Double Width Bracket

Martin - VDO Atomic Dot Double Width Bracket

Sound Projects - X-act V2

€1,380.00 Excl. Tax
Availability:
On request
Art. code
SP-30.0105

Sound Projects - X-act V2

The legend refined! For more than 25 years the X-act is proving to be a most reliable, optimum blend of faithful audio reproduction and versatility. The V2 version is technically and optically improved. Like its predecessor, the new X-act can immediately be recognised by its perfect voice reproduction. This is because the human ear is extremely sensitive to deviations in this vital part of the frequency spectrum.

The X-act V2 housing combines a lightweight, TSG moulded, ergonomical cabinet construction with aluminum reinforcing which is 2,4 kg lighter than the V1. The resulting 12,1 kg make the X-act a featherweight to handle, without affecting its ruggedness. The X-act V2 is a near perfect floor monitor, but also excells as elegant F.O.H. system, independent distributed system or any type of infill.

The SALC (Single Audio-logic Level Control) speaker management is an RMS based gain riding circuit which maintains the tonal balance of the sound as perceived by the human ear. Especially at high levels. State-of-the-art modelling techniques and acoustic simulation programs dictate rounded cabinet shapes, manifold reinforcing ribs and no parallel surfaces. A shared wave-guide properly loads the 1” and 10” drivers. The result is minimal coloration in the “speech-band“ over a wide, yet stable sweet listening spot.

V2 features:

  • Improved roadproof hexagon frontgrill
  • 2,4 kg weight reduction
  • 24bit/96Khz. low latency DSP filter board
  • Auto switching power supply (100~230V)
  • Improved bass control at higher max. SPL
  • Low standby power consumption (meets 2013 ErP Lot 6 0.5W requirements)

Acoustical specifications

  • Drivers: 1 x 1", 1 x 10" High power low weight Neodymium design.
  • Freq. response: 50Hz-20kHz
  • Max. peak SPL @1m: 130dB
  • Coverage angle: 100H x 40V

Electrical specifications

  • Amplifier(s): CoolClassD™ technology
  • Output: 500W sine (ALC limited)
  • Crossover: 1.6 kHz, 4th order
  • Filter subsonic: 40Hz, 2nd order
  • Input impedance: 20 kOhms balanced, 10 kOhms unbalanced
  • Output impedance: Hard-wired to input
  • Main voltage: 230V (other on request)
  • Mains frequency: 50/60 Hz
  • Idle:  < 50VA
  • Full load: 300 VA. SALC limited Ref. to continuous pink noise signal (12 dB crest factor within the specified range)
  • Protection: D.A.L.C. (Dual Audio Logic Control)

Additional descriptive data

  • Cabinet construction: Fully recyclable T.S.G. structural compound
  • Finish: Polyurethane coating
  • Weight: 12.1Kg
  • Size WxHxD (mm): 320 x 462 x 310
  • Rigging points: Fixing points M8 for flying bracket (optional), recessed pole mount
  • Audio connectors: IEC XLR-3 in/out
  • Main connectors: Powercon in, Powercon out
  • Max. operating temp: -10 to 40 C ambient
  • Comfortable single-hand carrying handle
More Information
Condition New
Brand Sound Projects
We found other products you might like